Effect of Co,Pd and Pt ultra-thin films on the Ni-silicide formation: investigating the sandwich configuration

The effect of Co, Pd and Pt ultrathin films on the kinetics of the formation of Ni-silicide by reactive diffusion is investigated. 50 nm Ni/1 nm X/ 50 nm Ni (X?=?Co, Pd, Pt) deposited on Si(100) substrates are studied using in-situ and ex-situ measurements by X-ray diffraction (XRD). The presence of Co, Pd or Pt thin films in between the Ni layers delays the formation of the metal rich phase compared to the pure Ni/Si system and thus these films act as diffusion barriers. A simultaneous silicide formation (δ-Ni₂Si and NiSi phases) different from the classic sequential formation is found during the consumption of the top Ni layer for which Ni has to diffuse through the barrier. A model for the simultaneous growth in the presence of a barrier is developed, and simulation of the kinetics measured by XRD is used to determine the permeability of the different barriers. Atom probe tomography (APT) of the Ni/Pd/Ni system shows that the Pd layer is located between the Ni top layer and δ-Ni₂Si during the silicide growth, in accordance with a silicide formation controlled by Ni diffusion through the Pd layer. The effect of the barrier on the silicide formation and properties is discussed.

     

Surface Modification of Co3O4 Nanosheets to Promote Peroxymonosulfate Activation for Degradation of Atrazine

Catalysis Letters - This study proposed a new facile route to rational creating oxygen-vacancy (Vo)-rich surface of Co3O4 nanosheets by acetic acid leaching. The acid leached Co3O4 nanosheets was...     

Multihead attention mechanism guided ConvLSTM for pixel-level segmentation of ocean remote sensing images

Multimedia Tools and Applications - Semantic segmentation of ocean remote sensing images classifies each pixel in the image according to the ocean background and island type, and is an important...     

关于多功能液压支架拖运车的电控系统设计

本文简介多功能液压支架拖运车的电控系统,包括电控箱的设计和主要电气元件的性能和选择依据。此电控系统能够一般电控系统的各种功能和保护,而且能够通过摄像头做到操作盲区和使用遥控器进行远程控制,从而提高液压支架的拖运效率、降低劳动强度和提高安全保障。     

地表径流速度对城市内涝影响规律

为分析地表径流速度对城市内涝的影响,采用一维地下排水管网与二维城区地形的动态耦合模型,选取大连市某排水区块作为研究区域,设置4种地表径流速度10种设计降雨场景,模拟分析在不同重现期设计降雨及不同地表径流速度下研究区的内涝积水特性。结果表明:随着地表径流速度降低,管道排水压力变小,管道排水达标率最高可提升48.05%,且降雨重现期越短,地表径流流速对管道排水压力的削减效果越明显;地表径流流速对检查井溢流量影响显著,随着地表径流速度降低,检查井溢流量峰值最高可减小2 750 m~3,峰现时间最长可滞后56 min,同时随着降雨重现期增长,地表径流流速对检查井溢流量的削减效果减弱;研究区低、高风险区淹没面积随地表径流速度降低,最高可分别减小1.64万、8.37万m~2,但中风险区淹没面积变化反复。     

Moderate temperature sintering of BaZr0.8Y0.2O3-δ protonic ceramics by A novel cold sintering pretreatment

The state-of-the-art protonic ceramic conductor BaZr_0.8Y_0.2O_3-δ (BZY20) requires an extremely high sintering temperature (≥1700 °C) to achieve the desired relative density and microstructure necessary to function as a proton conducting electrolyte. In this work, we developed a cold sintering pretreatment assisted moderate-temperature sintering method for the fabrication of high-quality pure BZY20 pellets. BZY20 pellets with high relative density of ~94% were fabricated with a final sintering temperature of 1500 °C (200 °C lower than the traditional sintering temperature). A comparison with BZY20 control samples indicated that the proper amount of BaCO₃ introduced on the BZY20 particle surface and the high green density achieved by cold sintering pretreatment were the main drivers for lowering the sintering temperature. The electrical conductivity measurement by electrochemical impedance spectroscopy showed that the as-prepared BZY20 pellets have a proton conductivity comparable to the state-of-the-art values. The cold sintering pretreatment outlined in this work has the potential to lower the sintering temperatures for similar types of protonic ceramic materials under consideration for a wide range of energy conversion and storage applications.